någon som vill hjälpa en med att få in box id på rätt ställe + att få det att uppdatera sig
#
# /var/tuxbox/config/newcamd/cardserv.cfg
#
# The new cardserver can run several cards at once. It detects cards being
# inserted and removed from configured card readers. Every card uses its
# own TCP port to listen for incoming client connections. Card readers, that
# are configured, but where no card is inserted, will not be initialized.
# Supported are both serial ports of dbox2 (SERIAL_PORT = 0, 1), Dreambox
# cardreaders (SERIAL_PORT = 0 (upper), SERIAL_PORT = 1 (lower)) and the
# Dreambox's serial port (SERIAL_PORT = 2). Supported CA systems are Seca,
# Viaccess, Irdeto, Viasat-NDS, Conax, Cryptoworks and Nagra1. Irdeto cards (or
# some of them) probably won't work in the Dreambox cardreaders, due to driver
# issues. In fact, the only Irdeto cards, that were successfully tested in
# Dreambox cardreaders, are the new Premiere cards and I2 cards. Premiere cards
# will ONLY work with betad (no sharing allowed for Premiere). Betad is a small
# subset of cardserver, using Unix Domain Sockets to communicate with newcamd.
# Also betad will only understand a very small subset of the options described
# here. Each instance of betad will only be able to serve exactly one card,
# while one instance of cardserver can serve multiple cards at the same time.
# Therefore betad is not able to handle the sc8in1. Betad configuration file is
# called betad.cfg. There is no special manual for betad.cfg, we everyone will
# be able to figure out, which cardserv.cfg options, described below, will also
# work in betad.cfg and which won't.
# Configuration consists of global (all cards) and local (single card) options.
# betad.cfg will of course only have one local (single card) section. The
# global section is located at the beginning of the file before the first
# SERIAL_PORT option. The SERIAL_PORT option is a "divider" between the global
# and the local sections, it also is a divider between options for different
# cards. The SC8IN1_SLOT options is a similar divider, but it divides only
# between different cards in the sc8in1 cam and the first SC8IN1_SLOT options
# has to preceeded by a SERIAL_PORT option. Some options may appear in the
# global as well as in local sections, in the case the option in the global
# section is a default for all cards, that don't have the same option in their
# particular local section. Options that appear in an incorrect section will
# be rejected with a "parse error" and the cardserver won't start. Betad will
# also reject all cardserver options, that aren't necessary or allowed for its
# operation. betad will understand the following options, of used correctly:
# SERIAL_PORT, BAUDRATE, USER, PARITY, CARD_DETECT_INVERT, CARD_DETECT_BIT and
# IGNORE_CARD_DETECT_SWITCH.
#
# You can also start cardserver multiple times by specifying different cfg
# files in the command line. Use only the name of the cfg file, the path of the
# file is always fixed to /var/tuxbox/config/newcamd (dbox2, Dreambox) or
# /etc/newcamd (i386)
#
# (G) = global section only
# (L) = local section only
# (A) = all sections
#
# 14 byte des key for the connection (A)
# DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
#
# id name of the cardserver (G)
# SERVER_NAME = cardserv
#
# debug port, lists all cards and their open connections (G)
# just telnet to it
# DEBUG_PORT = 12002
#
# entitlement port, lists entitlements of Seca, Conax and Cryptoworks cards
# just telnet to it
# ENTITLEMENT_PORT = 12003
#
# optional admin options (G)
# port for incoming camdcmd connections
# password and 14 byte des key for admin connections
# ADMIN_PORT = 12004
# ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
#
# Userlist (A)
# there can be multiple users, user 1 always do AU for the card
# additional AU users can be defined by adding "au" at the end of the USER line
# keep in mind that your card number will be sent to all AU users
# global user preceed local users in terms of userid
# lan/wan/spider gives the type of connection
# lan = local area network
# wan = wide area network (those connections can be rebuild with camdcmd wanon)
# connections from cardspider to "wan" declared cards in cardserver are not
# possible
# spider = acts like wan, but allows connections from cardspider
# <username> <password> <lan/wan/spider> <newcamd hostname> <newcamd incoming cws port> (A)
# everything starting from <lan/wan> is optional (reverse login is optional)
# USER = dummy dummy lan dbox2 12000
# two examples for additional AU users
# USER = dummy2 dummy2 lan dbox2 12000 au
# USER = dummy3 dummy3 au
#
# CLIENT_CONNECT_TIMEOUT (in 100ms) (G)
# max time to wait for a login at a newcamd client
# CLIENT_CONNECT_TIMEOUT = 20
#
# debug options (A) - show network and card init, ecm and emm packages
# DEBUG_INIT = no
# DEBUG_NET = no
# DEBUG_ECM = no
# DEBUG_EMM = no
#
# Serial Port (Phoenix/Multicam) (Section divider)
# The first SERIAL_PORT options ends the global section
# On DM7000 SERIAL_PORT = 0 is the upper card slot,
# SERIAL_PORT = 1 is the lower card slot and 2 is the
# actual serial port.
# On DM500 SERIAL_PORT = 1 is the card slot, 2 is the
# serial port.
# All numbers SERIAL_PORT = 3 and higher on Dreambox will use /dev/usb/tts/X
# devices for Phoenix on USB-to-RS232 adapters. This feature depends on a
# driver for your particular SB->RS232 adapter being insmod into the kernel of
# your image, your particular USB->RS232 driver supporting RS232 handshaking
# signal generation and on the particular card used. Basically this feature
# should be considered unstable and for advanced users only. The BAUDRATE option
# is not available for SERIAL_PORT = 3 and higher on Dreambox and would be
# rejected with a parse error
# SERIAL_PORT = <no> begins a single card's local section
# SERIAL_PORT = 0
#
# Serial Port (sc8in1) (section devider)
# SERIAL_PORT = <no> sc8in1 begins a sc8in1 description
# SC8IN1_SLOT must follow immediately to start a local section
# SERIAL_PORT = 1 sc8in1
#
# sc8in1 slot (sc8in1 sub section divider)
# valid slots are 0-7, 0 being the left most connector on the sc8in1
# SC8IN1_SLOT = 1
#
# Parity - serial communication parameter for the smartcard (L)
# The default is on, which is correct for all cards except Irdeto
# This is for reading the ATR only, after the ATR has been recognized by
# cardserver, it automatically switches to the correct communication parameters
# Some Irdeto cards work with PARITY = on also, some need PARTIY = off, so just
# test it. Dreambox cardreaders don't need this option, so it will be rejected
# for SERIAL_PORT = 0, 1 on Dreambox
# PARITY = on
#
# CARD_DETECT_BIT (L)
# different Phoenix readers sometimes use different serial lines to detect an
# inserted card, here you can specify, which line cardserver should use for a
# particular card. Possible values are CTS, DCD and DSR
# Default is CTS for sc8in1 and dbox2 serport 1, DCD otherwise
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_BIT = DCD
#
# Baudrate (L) (DBOX2/DREAMBOX versions ONLY!)
# Baudrate selection for the dbox2/Dreambox server. Allows to run 6 MHz with
# 3.579 MHz crystal and (theoretically) the other way around.
# Keep in mind, running anything but Irdeto cards at 6 MHz is overclocking!!!
# Irdeto card at 3.57 MHz: BAUDRATE = 5727
# other card at 6 MHz: BAUDRATE = 16128
# Default is 9622, which is correct for all except Irdeto cards at 3.579 MHz
# 3579545 Hz / 372 = 9622 bit/s (see iso 7816)
# This option will be rejected on I386 and on Dreambox ports other than
# SERIAL_PORT = 2
# BAUDRATE = 9622
#
# TCP port (L) - the port listening for connections for a particular card
# TCP_PORT = 2000
#
# EMM options - block EMM-U, EMM-G or EMM-S (A)
# EMM-G = no
# EMM-S = no
# EMM-U = no
#
# For iso cardreaders that close the card switch contact instead of opening it,
# when a card is inserted (L)
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_INVERT = yes
#
# Disable Pin (L) Seca only
# suppress all pin enter requests on Seca cards
# be very careful with this feature, if you have ordered PPV events or have
# prepaid Jetons on your card, if this is enabled, cardserver will use them
# up on any ppv event without ever asking
# DISABLE_PIN = yes
#
# Special features (only for some cards) (L)
# SPECIAL_FEATURES = no
#
# Exclude services - Some providers offer a PPV preview by allowing a card
# to decrypt a certain number of ECMs of each PPV event before it has to be
# bought. Sharing such a card with other people allows them to "steal" this
# PPV preview. With this option, you can tell cardserver to not ask the card
# to decrypt ECMs for certain services, except if user 1 (the EMM user) asks
# for them. Each blocked service has to be listed with its service id.
# A service id is a 16-bit number and has to be given in hex.
# camdcmd offers a possibility to change the list of blocked services without
# restarting cardserver (if for example you have bought a PPV event and now
# want to share it).
#
# Block single service (L)
# EXCLUDE_SERVICE = 13a9
# You can also block a range of service ids, the following blocks all services
# from 02be to 02c8
# EXCLUDE_SERVICE_MULTIPLE = 02be:02c8
#
# Boxid (for Viasat-NDS cards only) (L)
# 10-digit serial number of the STB, your Viasat card is married to
# you find this serial number on your original Viasat STB in the following menu:
# Setup->Decoder information->STB Identifier
# take this number and remove the last digit
# take the first (left-most) 10 digits, omit the last (right-most) digit
#BOXID = 0000000000
#
# Boxkey (for Nagra1 cards only) (L)
# 8 byte des boxkey of your nagra smartcard. This boxkey is needed for proper
# use of your card, otherwise you'll get incorrect control words
# BOXKEY = 11 22 33 44 55 66 77 88
#
# Example
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserv
DEBUG_PORT = 14000
ENTITLEMENT_PORT = 14001
ADMIN_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
USER = local local lan 127.0.0.1 12000
USER = spider spider lan 127.0.0.1 15003
DEBUG_INIT = no
DEBUG_NET = no
DEBUG_ECM = no
DEBUG_EMM = no
#SERIAL_PORT = 0
#TCP_PORT = 10000
SERIAL_PORT = 1
TCP_PORT = 10001
SERIAL_PORT = 1