installerade idag newcs tillsamans med mgcamd fick kortet att hoppa igång men nätverkslampan började blinka som fxxxn vet ej vad det är för fel .
Kör en db800hd med image lt6 postar min newcard list härså får ni se hur den ser ut.
#
CWS = 127.0.0.1 10000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS_CONNECT_TIMEOUT = 20
CWS_INCOMING_PORT = 12000
CWS_KEEPALIVE = yes
#
:confused:
kolla i /var/keys/mg_cfg (eller vart den nu ligger på din box) i sektionen:
--------
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 192.168.1.39 8888 /tmp/mgcamd.log
-----------------
kolla så inte det står L: { 01 } vilket betyder att mgcamd skickar loggen ut på nätverket
hjälpte inte med L 00 blinkar sombara den ändå
så här ser min mgconfig ut .
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 192.168.1.39 8888 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# map all 180x nagra caids to 1801
# default is 01
F: { 01 }
L: { 03 }
Betyder både val 01 och 02 = 03 så du har både nätverks log och log till konsollen,
startade du om mgcamd efter det att du satt den till L: { 00 } ?
så här ser min newcamd list .
#
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS =127.0.0.1 10000
dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
och min newcs xml.
<?xml version="1.0"?>
-<newCSconfig> -<readers name="Card Readers"> -<device> <name>lower</name> <type>Sci</type> <mhz>357</mhz> <node>/dev/sci0</node> <parity>even</parity> <export>yes</export> <enabled>yes</enabled> <blocksa>no</blocksa> <blockua>no</blockua> <blockga>no</blockga> <boxid/> <PTShandshake>no</PTShandshake> <Seca-PPV>no</Seca-PPV> <crypto-special>no</crypto-special> <carddetect>yes</carddetect> <newcamd_port>10000</newcamd_port> <autosid>yes</autosid> <priority>round</priority> </device> -<device> <name>upper</name> <type>Sci</type> <node>/dev/sci1</node> <parity>even</parity> <export>yes</export> <enabled>yes</enabled> <blocksa>no</blocksa> <blockua>no</blockua> <blockga>no</blockga> <boxid/> <PTShandshake>no</PTShandshake> <Seca-PPV>no</Seca-PPV> <crypto-special>no</crypto-special> <carddetect>yes</carddetect> <newcamd_port>10001</newcamd_port> <autosid>yes</autosid> <priority>round</priority> </device> </readers> -<radegastserver> <enabled>no</enabled> <port>10003</port> <allow>ALL</allow> </radegastserver> -<cache> <emm>20</emm> <ecm>-1</ecm> </cache> -<debug> <level>normal</level> <type>init</type> <output>console,udp,tcp</output> <logfile/> <console_options/> <file_options/> <udp_host>192.168.1.100</udp_host> <udp_port>1000</udp_port> <udp_options/> <tcp_port>3001</tcp_port> <tcp_options/> </debug> -<httpd> -<server> <port>8080</port> <enabled>yes</enabled> </server> -<user> <name/> <password/> <accesslevel>admin</accesslevel> </user> </httpd> -<newcamdserver> <enabled>yes</enabled> <deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey> <name>newcs</name> <userfile>/tmp/users.txt</userfile> -<user> <name>dummy</name> <password>dummy</password> <au>on</au> <allow>lower</allow> <allow>upper</allow> </user> </newcamdserver> </newCSconfig>
så här ser min newcamd list .
#
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS =127.0.0.1 10000
dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
Det ska inte vara en radbrytning efter "10000".
Det ska alltså stå:
CWS =127.0.0.1 10000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
Prova att kopla ihop boxen med en dator med en korsad nätverkskabel eller koppla in en hub och kolla vad boxen håller på att skicka ut på nätverket genom att använda wireshark (sök efter wireshark på google) viss trafik kan du även se om du använder en switch
Powered by vBulletin™ Version 4.2.5 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.