-
AU i cardserver.i386
Hej ! har sett att många haft problenm med auto uppdate i cardserver.i386
Det första ni ska göra är att logga in på dreamboxen med något ftp program. gå in i mappen var/keys och öppna mg_conf. kolla här under så ni har samma inställningar som denna:
Kod:
# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }
# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }
# AU
# 01 enable AU
# 02 AU Auto
A: { 01 }
# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 01 }
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
O: { 00 }
# on screen display Options
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }
# Log options
# 00 Off
# 01 Network
# 02 console
# 03 both
L: { 02 } 172.16.1.1 28007
# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# use summ
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 04 Emm cache for network cards
H: { 07 }
# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }
# debug, use summ
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 02 }
# keep ecm cache, seconds
E: { 15 }
Sen ska ni skriva in i servern efter användare:
Kod:
USER = polare7 polar7 lan 192.168.1.103 12000 au
sen ske det INTE stå au efter cws raderna i newcamd filen i servern !
det ska se ut så här:
CWS = ip till servern 10000 polis7 polis7 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserv
och detta ska stå ovanför cws-raderna någonstans:
FUNKAR FÖR MEJ BÅDE MED VIASAT O CH CD
MVH PEPPE
