Konfigurera 7025 med Viasat
Jag har nu suttit och försökt fram och tillbaka med att få igång en DM7025 med Viasatkort i tre veckor.
Har följande i boxen LT-Fifth-dm7025, evocamd_2.12, newcs_1.19 men har testat en rad olika.
Mina frågor
1. Har sökt på sirius(5E) men hittar bl.a inte TV3 som ingår i viasat utbudet, vad beror detta på?
2. Några kanaler som tv1,tv2,24, kanal5 kan jag få in med hackig men frusen bild oftast. Men med orgboxen är det klockren bild. Varför?
3. Hur ser man på telnet om boxern hittar kortet?
4. Ser mina configfiler bra ut, eller går det att konfa mera?
P.s. Kör Viasat kortet i Dm lokalt.
Mycket tacksam för hjälp!!
newcamd.conf /etc/tuxbox/config
CWS = localhost 62000 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
CWS = localhost 62001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan cardserver
# /var/tuxbox/config/newcamd.conf
#
# this is the configfile for MGCamd with NewCS!!!!
#
#
# What Demux API is used? (1 = very old, 2 = rel (Dreambox), 3 = head (VDR))
DEMUX_API = 2
# on PPC version: What Box is used? Valid options are DBOX2, DM7000 and DM5600
# on I386 version this parameter is ignored
BOX_TYPE = DM7000
# Which device for writing control words should be used?
# Valid options are CA, SDEV or GTX
# (SDEV and GTX = /proc/bus/gtx, CA = /dev/caX or /dev/dvb/card0/caX)
CONTROL_WORD_DEVICE = CA
# What CA0 API is used?
# 3 for recent DVB-S driver or recent Dreambox drivers (dream.o from 1.07.3)
# also for ca1 use on dbox2
# 2 for older Dreambox driver (ca.o or dream.o up to 1.07.2)
# no effect on PPC version if CONTROL_WORD_DEVICE = GTX or SDEV
CA_API = 3
# output control words to /proc/bus/gtx in 16 byte or 4096 byte packets
# no effect on I386 version or on PPC version, if BOX_TYPE = DREAMBOX
GTX_OUTPUT_MODE = 16
# This is important for channels which frequently change between free and
# encrypted broadcasts. The change will be reflected in the PMT. If you
# don't want your picture to stop when the channel goes from free access
# mode to encrypted mode, either your zapper (zapit/Enigma) or newcamd
# itself has to keep track of PMT changes. Recent Enigma versions do this,
# so you can set PMT_UPDATE_WATCH to no. Recent Zapit versions also have
# this option, but it is not compiled by default. So when using Zapit
# without PMT updates, you need to enable newcamd to monitor the PMT
# (PMT_UPDATE_WATCH = yes). Having both zapper and newcamd monitor
# the PMT at the same time, can lead to all kind of instabilities and
# should therefore by avoided, even if it seems to work at first.
PMT_UPDATE_WATCH = yes
# Use emulator?
EMU = yes
# if both control word server and emulator keys are available for the
# channel, which method should be tried first?
PREFER_EMU = yes
# deactivates the dbox2 Betacrypt CAM
# this has to be set to yes on Dreambox
DISABLE_CAM = yes
# use dbox2 Betacrypt CAM for caids 06, 17 or both (00)?
CAM_CASYS = 17
# Autoupdate for Emu and Control Word Servers
# AU is always yes if there are Betacrypt UDS control word server
# connected to newcamd
AU = yes
#
# newcamd debug options
#
# dumps all ca systems used by a channel on the console
SHOW_ALL_CA_SYSTEMS = no
# On Screen Display, neutrino, enigma or none
OSD = none
# Recent Enigma versions come with a new option "Use http authentication"
# in the Expert Setup menu. If this option is enabled, the Enigma web server
# requires all clients to authorize themselves with username (root) and
# password (usually dbox2 or dreambox). The following option tells newcamd
# about the authentication username and password to use for the web server
# in order to be able to display its on screen information.
OSD_WEB_LOGIN = root:dreambox
# print debug messages about ECM handling
DEBUG_ECM = yes
# print debug messages about EMM handling
DEBUG_EMM = no
# print debug messages about Control Word Server (CWS)
DEBUG_CWS = yes
# print debug messages about dbox2 CAM (cam-alpha.bin)
DEBUG_CAM = yes
# print command message to/from dbox2 CAM as hex strings
DEBUG_CAM_HEX = no
# print all plain control words used
SHOW_CW = no
# hex dump of entire PAT
SHOW_PAT = no
# hex dump of entire PMT
SHOW_PMT = no
# hex dump of entire ECM
SHOW_ECM = no
# hex dump of entire CAT
SHOW_CAT = no
# hex dump of entire EMM (AU)
SHOW_EMM = no
# show network ECM messages being sent and received from/to the cardservers
SHOW_CWS_ECM = no
# show network EMM messages being sent and received from/to the cardservers
SHOW_CWS_EMM = no
# hex dump of EMMs with wrong signature
EMM_REPORT_WRONG_SIG = no
# delay between channel zap and appearance of the OSD
OSD_WAIT_TIME = 2000
#
# newcamd optional settings
#
# Delay between reception of new control word and writing them into
# the CSA registers
# this is a default, can be changed for each individual key in keylist
DEFAULT_CW_DELAY = 500
# reload config on every channel zap
RELOAD_CONFIG_ON_ZAP = yes
# reload keylist on every channel zap
RELOAD_KEYLIST_ON_ZAP = no
# write osd ca info to file
# CA_INFO_FILE = /tmp/cainfo.txt
#
# newcamd mandatory settings for control word servers (cws)
#
# Cardserver list
#
# <hostname> <port> <username> <password> <14 byte triple-des key in hex> <lan/wan> <cardserver name>
#
# wan connections will be dropped and rebuild if newcamd is told so by camdcmd
# (see admin options)
#
# hostname = uds to use betad, port is the serial port in that case
#
#CWS = uds 1 premiere premiere
#CWS = 127.0.0.1 10001 local local 01 02 03 04 05 06 07 08 09 10 11 12 13 14 wan cardserv
#
# newcamd optional settings for using control word servers (cws)
#
# Timeout for cardserver login in 100ms
CWS_CONNECT_TIMEOUT = 20
# Port to listen for incoming cardserver connections (reverse login)
# and/or admin connections
CWS_INCOMING_PORT = 12000
# Port to get a list of all connected cardservers, just telnet to it
CWS_DEBUG_PORT = 12001
#
# newcamd admin control options
# (incoming port is the same as CWS_INCOMING_PORT)
#
# <password> <14 byte des key>
#
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
newcs.conf /etc/tuxbox/config
<?xml version="1.0"?>
<newCSconfig>
<readers name="Card Readers">
<device>
<name>Lower</name>
<type>sci</type>
<node>/dev/sci0</node>
<parity>even</parity>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>no</blockga>
<boxid></boxid>
<PTShandshake>no</PTShandshake>
<Seca-PPV>no</Seca-PPV>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>62000</newcamd_port>
<autosid>yes</autosid>
<priority>round</priority>
</device>
<device>
<name>Upper</name>
<type>sci</type>
<node>/dev/sci1</node>
<parity>even</parity>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>no</blockga>
<boxid></boxid>
<PTShandshake>no</PTShandshake>
<Seca-PPV>no</Seca-PPV>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>62001</newcamd_port>
<autosid>yes</autosid>
<priority>round</priority>
</device>
</readers>
<radegastserver>
<enabled>no</enabled>
<port>10003</port>
<allow>ALL</allow>
</radegastserver>
<cache>
<emm>10</emm>
<ecm>10</ecm>
</cache>
<debug>
<level>normal</level>
<type>init</type>
<output>console,udp,tcp</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.0.100</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<name>cardserver</name>
<userfile>/tmp/users.txt</userfile>
<user>
<name>local</name>
<password>local</password>
<au>on</au>
</user>
</newcamdserver>
</newCSconfig>
mg_cfg /usr/keys
# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }
# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }
# AU
# 00 is ignored (default)
# 01 enable AU
# 02 AU Auto
A: { 01 }
# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 02 }
# key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable (default)
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 03 }
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 60 }
# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
O: { 00 }
# on screen display Options
# 03 default
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }
# Log options
# 00 Off (default)
# 01 Network
# 02 console
# 03 both
L: { 00 } 172.16.1.1 28007
# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup,
# same syntax as restore.list
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 03 both caches
H: { 00 }
# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }
# debug
# 00 off (default)
# 01 on
D: { 00 }Spara filen och stäng DCC.
