hej!
om jag har ett viasat orginalkort som funkar om jag sätter in den i en dreambox och knappar in boxid och nått annat kan jag titta på de kanaler då .
Tack i förväg
Utskriftsvy
hej!
om jag har ett viasat orginalkort som funkar om jag sätter in den i en dreambox och knappar in boxid och nått annat kan jag titta på de kanaler då .
Tack i förväg
Ja.
mvh humlan.
kan man titta utan kort sen. Vilka nummer ska man knappa in och vart hittar man de. Ska man bara knappa in de eller?
Nej, du måste ha ett kort i.
Jo du borde kunna ta ut kortet och köra...
....i 10 sekunder sen behöver en ny nyckel läsas från kortet!
blir ju bra träning för armen iaf :)
någon som vill hjälpa en med att få in box id på rätt ställe + att få det att uppdatera sig
#
# /var/tuxbox/config/newcamd/cardserv.cfg
#
# The new cardserver can run several cards at once. It detects cards being
# inserted and removed from configured card readers. Every card uses its
# own TCP port to listen for incoming client connections. Card readers, that
# are configured, but where no card is inserted, will not be initialized.
# Supported are both serial ports of dbox2 (SERIAL_PORT = 0, 1), Dreambox
# cardreaders (SERIAL_PORT = 0 (upper), SERIAL_PORT = 1 (lower)) and the
# Dreambox's serial port (SERIAL_PORT = 2). Supported CA systems are Seca,
# Viaccess, Irdeto, Viasat-NDS, Conax, Cryptoworks and Nagra1. Irdeto cards (or
# some of them) probably won't work in the Dreambox cardreaders, due to driver
# issues. In fact, the only Irdeto cards, that were successfully tested in
# Dreambox cardreaders, are the new Premiere cards and I2 cards. Premiere cards
# will ONLY work with betad (no sharing allowed for Premiere). Betad is a small
# subset of cardserver, using Unix Domain Sockets to communicate with newcamd.
# Also betad will only understand a very small subset of the options described
# here. Each instance of betad will only be able to serve exactly one card,
# while one instance of cardserver can serve multiple cards at the same time.
# Therefore betad is not able to handle the sc8in1. Betad configuration file is
# called betad.cfg. There is no special manual for betad.cfg, we everyone will
# be able to figure out, which cardserv.cfg options, described below, will also
# work in betad.cfg and which won't.
# Configuration consists of global (all cards) and local (single card) options.
# betad.cfg will of course only have one local (single card) section. The
# global section is located at the beginning of the file before the first
# SERIAL_PORT option. The SERIAL_PORT option is a "divider" between the global
# and the local sections, it also is a divider between options for different
# cards. The SC8IN1_SLOT options is a similar divider, but it divides only
# between different cards in the sc8in1 cam and the first SC8IN1_SLOT options
# has to preceeded by a SERIAL_PORT option. Some options may appear in the
# global as well as in local sections, in the case the option in the global
# section is a default for all cards, that don't have the same option in their
# particular local section. Options that appear in an incorrect section will
# be rejected with a "parse error" and the cardserver won't start. Betad will
# also reject all cardserver options, that aren't necessary or allowed for its
# operation. betad will understand the following options, of used correctly:
# SERIAL_PORT, BAUDRATE, USER, PARITY, CARD_DETECT_INVERT, CARD_DETECT_BIT and
# IGNORE_CARD_DETECT_SWITCH.
#
# You can also start cardserver multiple times by specifying different cfg
# files in the command line. Use only the name of the cfg file, the path of the
# file is always fixed to /var/tuxbox/config/newcamd (dbox2, Dreambox) or
# /etc/newcamd (i386)
#
# (G) = global section only
# (L) = local section only
# (A) = all sections
#
# 14 byte des key for the connection (A)
# DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
#
# id name of the cardserver (G)
# SERVER_NAME = cardserv
#
# debug port, lists all cards and their open connections (G)
# just telnet to it
# DEBUG_PORT = 12002
#
# entitlement port, lists entitlements of Seca, Conax and Cryptoworks cards
# just telnet to it
# ENTITLEMENT_PORT = 12003
#
# optional admin options (G)
# port for incoming camdcmd connections
# password and 14 byte des key for admin connections
# ADMIN_PORT = 12004
# ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
#
# Userlist (A)
# there can be multiple users, user 1 always do AU for the card
# additional AU users can be defined by adding "au" at the end of the USER line
# keep in mind that your card number will be sent to all AU users
# global user preceed local users in terms of userid
# lan/wan/spider gives the type of connection
# lan = local area network
# wan = wide area network (those connections can be rebuild with camdcmd wanon)
# connections from cardspider to "wan" declared cards in cardserver are not
# possible
# spider = acts like wan, but allows connections from cardspider
# <username> <password> <lan/wan/spider> <newcamd hostname> <newcamd incoming cws port> (A)
# everything starting from <lan/wan> is optional (reverse login is optional)
# USER = dummy dummy lan dbox2 12000
# two examples for additional AU users
# USER = dummy2 dummy2 lan dbox2 12000 au
# USER = dummy3 dummy3 au
#
# CLIENT_CONNECT_TIMEOUT (in 100ms) (G)
# max time to wait for a login at a newcamd client
# CLIENT_CONNECT_TIMEOUT = 20
#
# debug options (A) - show network and card init, ecm and emm packages
# DEBUG_INIT = no
# DEBUG_NET = no
# DEBUG_ECM = no
# DEBUG_EMM = no
#
# Serial Port (Phoenix/Multicam) (Section divider)
# The first SERIAL_PORT options ends the global section
# On DM7000 SERIAL_PORT = 0 is the upper card slot,
# SERIAL_PORT = 1 is the lower card slot and 2 is the
# actual serial port.
# On DM500 SERIAL_PORT = 1 is the card slot, 2 is the
# serial port.
# All numbers SERIAL_PORT = 3 and higher on Dreambox will use /dev/usb/tts/X
# devices for Phoenix on USB-to-RS232 adapters. This feature depends on a
# driver for your particular SB->RS232 adapter being insmod into the kernel of
# your image, your particular USB->RS232 driver supporting RS232 handshaking
# signal generation and on the particular card used. Basically this feature
# should be considered unstable and for advanced users only. The BAUDRATE option
# is not available for SERIAL_PORT = 3 and higher on Dreambox and would be
# rejected with a parse error
# SERIAL_PORT = <no> begins a single card's local section
# SERIAL_PORT = 0
#
# Serial Port (sc8in1) (section devider)
# SERIAL_PORT = <no> sc8in1 begins a sc8in1 description
# SC8IN1_SLOT must follow immediately to start a local section
# SERIAL_PORT = 1 sc8in1
#
# sc8in1 slot (sc8in1 sub section divider)
# valid slots are 0-7, 0 being the left most connector on the sc8in1
# SC8IN1_SLOT = 1
#
# Parity - serial communication parameter for the smartcard (L)
# The default is on, which is correct for all cards except Irdeto
# This is for reading the ATR only, after the ATR has been recognized by
# cardserver, it automatically switches to the correct communication parameters
# Some Irdeto cards work with PARITY = on also, some need PARTIY = off, so just
# test it. Dreambox cardreaders don't need this option, so it will be rejected
# for SERIAL_PORT = 0, 1 on Dreambox
# PARITY = on
#
# CARD_DETECT_BIT (L)
# different Phoenix readers sometimes use different serial lines to detect an
# inserted card, here you can specify, which line cardserver should use for a
# particular card. Possible values are CTS, DCD and DSR
# Default is CTS for sc8in1 and dbox2 serport 1, DCD otherwise
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_BIT = DCD
#
# Baudrate (L) (DBOX2/DREAMBOX versions ONLY!)
# Baudrate selection for the dbox2/Dreambox server. Allows to run 6 MHz with
# 3.579 MHz crystal and (theoretically) the other way around.
# Keep in mind, running anything but Irdeto cards at 6 MHz is overclocking!!!
# Irdeto card at 3.57 MHz: BAUDRATE = 5727
# other card at 6 MHz: BAUDRATE = 16128
# Default is 9622, which is correct for all except Irdeto cards at 3.579 MHz
# 3579545 Hz / 372 = 9622 bit/s (see iso 7816)
# This option will be rejected on I386 and on Dreambox ports other than
# SERIAL_PORT = 2
# BAUDRATE = 9622
#
# TCP port (L) - the port listening for connections for a particular card
# TCP_PORT = 2000
#
# EMM options - block EMM-U, EMM-G or EMM-S (A)
# EMM-G = no
# EMM-S = no
# EMM-U = no
#
# For iso cardreaders that close the card switch contact instead of opening it,
# when a card is inserted (L)
# Will be rejected for SERIAL_PORT = 0, 1 on Dreambox (internal cardreaders)
# CARD_DETECT_INVERT = yes
#
# Disable Pin (L) Seca only
# suppress all pin enter requests on Seca cards
# be very careful with this feature, if you have ordered PPV events or have
# prepaid Jetons on your card, if this is enabled, cardserver will use them
# up on any ppv event without ever asking
# DISABLE_PIN = yes
#
# Special features (only for some cards) (L)
# SPECIAL_FEATURES = no
#
# Exclude services - Some providers offer a PPV preview by allowing a card
# to decrypt a certain number of ECMs of each PPV event before it has to be
# bought. Sharing such a card with other people allows them to "steal" this
# PPV preview. With this option, you can tell cardserver to not ask the card
# to decrypt ECMs for certain services, except if user 1 (the EMM user) asks
# for them. Each blocked service has to be listed with its service id.
# A service id is a 16-bit number and has to be given in hex.
# camdcmd offers a possibility to change the list of blocked services without
# restarting cardserver (if for example you have bought a PPV event and now
# want to share it).
#
# Block single service (L)
# EXCLUDE_SERVICE = 13a9
# You can also block a range of service ids, the following blocks all services
# from 02be to 02c8
# EXCLUDE_SERVICE_MULTIPLE = 02be:02c8
#
# Boxid (for Viasat-NDS cards only) (L)
# 10-digit serial number of the STB, your Viasat card is married to
# you find this serial number on your original Viasat STB in the following menu:
# Setup->Decoder information->STB Identifier
# take this number and remove the last digit
# take the first (left-most) 10 digits, omit the last (right-most) digit
#BOXID = 0000000000
#
# Boxkey (for Nagra1 cards only) (L)
# 8 byte des boxkey of your nagra smartcard. This boxkey is needed for proper
# use of your card, otherwise you'll get incorrect control words
# BOXKEY = 11 22 33 44 55 66 77 88
#
# Example
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserv
DEBUG_PORT = 14000
ENTITLEMENT_PORT = 14001
ADMIN_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
USER = local local lan 127.0.0.1 12000
USER = spider spider lan 127.0.0.1 15003
DEBUG_INIT = no
DEBUG_NET = no
DEBUG_ECM = no
DEBUG_EMM = no
#SERIAL_PORT = 0
#TCP_PORT = 10000
SERIAL_PORT = 1
TCP_PORT = 10001
SERIAL_PORT = 1
Hmmm.
Totalt oläsligt.
Ta bort alla rader som börjar med #, och posta den på nytt. OBS Editera den INTE i någon fönstermaskin, de ställer bara till med elände på filerna.
Lycka till
nästan alla
Boxid (for Viasat-NDS cards only) (L)
# 10-digit serial number of the STB, your Viasat card is married to
# you find this serial number on your original Viasat STB in the following menu:
# Setup->Decoder information->STB Identifier
# take this number and remove the last digit
# take the first (left-most) 10 digits, omit the last (right-most) digit
# BOXID = 0000000000
#
# Boxkey (for Nagra1 cards only) (L)
# 8 byte des boxkey of your nagra smartcard. This boxkey is needed for proper
# use of your card, otherwise you'll get incorrect control words
# BOXKEY = 11 22 33 44 55 66 77 88
#
# Example
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserv
DEBUG_PORT = 14000
ENTITLEMENT_PORT = 14001
ADMIN_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
USER = local local lan 127.0.0.1 12000
USER = spider spider lan 127.0.0.1 15003
DEBUG_INIT = no
DEBUG_NET = no
DEBUG_ECM = no
DEBUG_EMM = no
#SERIAL_PORT = 0
#TCP_PORT = 10000
SERIAL_PORT = 1
TCP_PORT = 10001
har laddat ner cam newcamd 6,02 komplit
till db
Så här kan den se ut typ
#
# /var/tuxbox/config/cardserv.cfg
# DREAMBOX 7020 /etc/tuxbox/config/cardserv.cfg
# edit by Ubbe mod@dreamboxx.nu
#
DESKEY = 01 02 03 04 05 06 07 08 09 10 11 12 13 14
SERVER_NAME = cardserv
DEBUG_PORT = 14000
ENTITLEMENT_PORT = 14001
ADMIN_PORT = 14002
ADMIN_PASSWORD = secret 00 00 00 00 00 00 00 00 00 00 00 00 00 00
USER = local local lan 127.0.0.1 12000
DEBUG_INIT = no
DEBUG_NET = no
DEBUG_ECM = no
DEBUG_EMM = no
# vill du använda ett Viasat-nds kort så ta bort tecknet # före boxid =
# och skriv in aktuellt nummer
#Upper Card slot
SERIAL_PORT = 0
TCP_PORT = 10000
BOXID = xxxxxxxxxx
EMM-G = yes
EMM-S = yes
EMM-U = yes
SPECIAL_FEATURES = no
#Lower Card Slot
SERIAL_PORT = 1
TCP_PORT = 10001
# BOXID = 0000000000
EMM-G = yes
EMM-S = yes
EMM-U = yes
SPECIAL_FEATURES = no
# SERIAL_PORT = 2
# TCP_PORT = 10002
# BOXID = 0000000000
# EMM-G = yes
# EMM-S = yes
# EMM-U = yes
# SPECIAL_FEATURES = no