hej, har nyss införskaffat mig en 600c istället för en 500c men får inte 600c att dekoda helt enkelt.
Jag har prövat olika gemini images, 4.3, 4.1 och 3.6 alla med samma fel.
Jag har även prövat mgcamd 1.27 samt newcamd och evocamd, alla med samma fel där också.
Jag flashar med nollmodemkabel och dreamup.
Min config är precis likadan som när jag hade 500c dvs följande för newcamd.conf
Kod:PREFER_EMU = yes
AU = yes
OSD_TIMEOUT = 1
OSD_WEB_LOGIN = root:dreambox
SHOW_ALL_CA_SYSTEMS = no
DEBUG_ECM = yes
DEBUG_EMM = no
DEBUG_CWS = yes
DEBUG_CAM = yes
SHOW_PAT = no
SHOW_PMT = no
SHOW_ECM = no
SHOW_CAT = no
SHOW_EMM = no
SHOW_CWS_ECM = no
SHOW_CWS_EMM = no
EMM_REPORT_WRONG_SIG = no
DEFAULT_CW_DELAY = 0
RELOAD_CONFIG_ON_ZAP = yes
RELOAD_KEYLIST_ON_ZAP = no
CA_INFO_FILE = /tmp/cainfo.txt
CWS = IP PORT USERNAME LÖSENORD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 lan cardserv
CWS = IP PORT USERNAME LÖSENORD 00 00 00 00 00 00 00 00 00 00 00 00 00 00 lan cardserv
CWS_CONNECT_TIMEOUT = 20
CWS_INCOMING_PORT = 12000
CWS_DEBUG_PORT = 12001
CWS_KEEPALIVE = yes
ADMIN_PASSWORD = LÖSENORD 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Min mg_cfg:
mg_cfg ligger i /var/keysKod:
# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }
# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }
# AU
# 01 enable AU
# 02 AU Auto
A: { 02 }
# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 01 }
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 01 }
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
O: { 02 }
# on screen display Options
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 15 }
# Log options
# 00 Off
# 01 Network
# 02 console
# 03 both
L: { 02 } 172.16.1.1 28007
# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# use summ
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 04 Emm cache for network cards
H: { 07 }
# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 01 }
# debug, use summ
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
D: { 31 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 02 }
# keep ecm cache, seconds
E: { 15 }
min newcamd.conf ligger i /var/tuxbox/config/newcamd/
har även prövat med att göra en kopia på newcamd.conf och lägga i /var/tuxbox/config/
Detta är nu min sista utväg, hållt på i runt 12 timmar med detta men får det inte att fungera :(
