Utskriftsvy
Hi,
I am completely new to owning and using a dreambox and would very much appreciate any help with configuring it.
I have acquired a Dreambox DM800C and a valid Com Hem subscription. I have flashed it with Gemini 4.1 and a channel search located all the expected channels.
However, inserting the Com Hem card with the chip faced down only lets me view the Com Hem channel. All other channels shows a blank screen.
Can anyone please help me with how and what I still need to install and configure?
Well you must install a cam first. It used to work with Evocamd (which you can get via the blue panel, but I am not sure if the new versions will work) and with Gbox on my DM7025.
I will try to get Comhem card working on my new DM8000 now too so I am curious too which cam work, will experiment.
Install CCcam 2.1.0. Download via blue panel -> Binary + Config file and start CCcam then you will have picture...
Thank you for your replies.
I used the blue panel -> settings -> addons -> download (Gemini-server)
and installed Cam -> CCcam 2.1.0 - Complete
and Cam-Configs -> CCcam-Config 2.1.0 - 27.03.2009
Then I switched on Auto-Camd and changed Default Camd -> CCcam 2.1.0 under Auto-Camd settings
I restartet Camd and restartet the dreambox.
Now I still don't get any picture but I do get sound on SVT2 only. I still get sound and picture on the Com Hem channel.
I tried the same with Evocamd and a few others but didn't get any picture or sound that way.
Is there any steps that I am missing? any suggestions?
This is the output of >CCcam_2.1.0 -dv
12:10:55.117 CCcam: ================================================== ====================
12:10:55.122 CCcam: starting CCcam 2.1.0 compiled on Mar 19 2009@21:27:26
12:10:55.123 CCcam: ================================================== ====================
12:10:55.124 CCcam: online using nodeId a41042d2fbdd8cd7
12:10:55.143 CCcam: dvb api3 detected
12:10:55.146 CCcam: DM800 detected
12:10:55.147 CCcam: create 8 cam device(s)
Segmentation fault
Try to upgrade the drivers in Gemini.Citat:
Ursprungligen postat av 3Cs
In telnet type:
ipkg install http://dreamboxupdate.com/opendreamb...0-r0_dm800.ipk
Restart the box when upgrade is complete and try to start CCcam manually again to see if your card is detected.
Also try an older version of CCcam or run NewCS with MgCamd.
I tried upgrading the drivers and now I get this (still with CCcam 2.1.0):
16:52:52.432 CCcam: ================================================== ====================
16:52:52.438 CCcam: starting CCcam 2.1.0 compiled on Mar 19 2009@21:27:26
16:52:52.439 CCcam: ================================================== ====================
16:52:52.440 CCcam: online using nodeId fbaca4ed0ba7e5a8
16:52:52.459 CCcam: dvb api3 detected
16:52:52.462 CCcam: DM800 detected
16:52:52.463 CCcam: create 8 cam device(s)
16:52:52.624 CCcam: card init fail
16:52:52.627 CCcam: readKeyfile: cannot open /var/keys/SoftCam.Key or not found
16:52:52.628 CCcam: readKeyfile: cannot open /var/keys/AutoRoll.Key or not found
16:52:52.628 CCcam: static cw not found or bad
16:52:52.630 CCcam: parsed 0 entries from /var/etc/CCcam.prio
16:52:52.707 CCcam: added 510 provider names from /var/etc/CCcam.providers
16:52:52.709 CCcam: added 4 channel names from /var/etc/CCcam.channelinfo
16:52:52.712 CCcam: server started on port 12000
16:52:52.722 CCcam: no working cam devices, no need to start pmthandler
Do I need to make any changes in any config files or other when installing eg. CCcam or NewCS?
Nope, if you have your card in the box you don't have to change anything in config files.
This is why you don't get any picture: 16:52:52.624 CCcam: card init fail
Try an older version of CCcam or MgCamd with NewCS...
I managed to get Comhem's card working in DM8000 with CCcam 2.0.11/NewCS 1.65
Do not use CCcam 2.1.0, it's buggy (I got Segmentation fault and Card init fail with it too). Get CCcam 2.0.11 and NewCS 1.65 binaries from the blue panel and their respective configs too.
Then setup camd to CCcam 2.0.11/NewCS 1.65 and restart the camd. If you still don't get the image remove the card and restart the box without it. After it started correctly put the card in, switch the channels and wait for the picture.
Thank you very much for your help :)
I finally (suddenly) got it working with Mgcamd 1.31/NewCS 1.65. I had tried several times both with CCcam 2.1.0, 2.0.11, Evocamd, and Mgcamd without luck - but I guess I had done something wrong those times because now it works. :)
One thing I did do different this time was - instead of restarting the box after installing the camd - I put it into 'deep standby', powered it off and back on again - when it came online I had picture. :)
So thanks again for the assistance. :thumbup:
Yes, MGcamd/NewCS seems to be the best option for Comhem card. It starts fine and even updates the card with new entitlements.
It can also work with CCcam/NewCS but you have to use CCcam 2.0.11, not 2.1 and you can't start with the card inside, otherwise CCcam stucks with segmentation fault. The updates do not work either so I have to switch to MGcamd for update every month. :)
hej jag har en dreambox 800c som jag undrar hur jag ska koppla in?
jag har 3 hål i väggen och den mittersta är ju upptagen av mitt internet?? hur gör jag för att få bild på mitt comhem abonnemang?
HJÄLP
Om du inte redan har det så är det dags att skaffa en router så löser det nätverksproblemet ivf
menar du att man får tv signalen via routern
jag måste väl ha en tv antenn sladd
Ja, du måste ha antennkabel inkopplad, men vad har den med uttaget till internet att göra? Sätt in antennkabeln där den ska sitta!Citat:
Ursprungligen postat av notto
Citat:
Ursprungligen postat av notto
Innan du kan se nått öht så måste du lägga in en ny image + cam och då behöver du tillgång till nätet, sen att man behöver antennsladden isatt tog jag som självklart :rolleyes:Citat:
Ursprungligen postat av Albino25