Via 093e slutat funkar idag? nån fler?

[JoeBlaze]

Oscam kan uppdatera det. Start oscam, när din client ansluter, står det AU enabled for user XX ? Ser du att den skickar EMM till oscam i loggen om du står på en viasat kanal?....

[cornholio]

Efter ett uppdatering via orginalboxen så funkar då allt igen för mig. Men varför inte oscam tog uppdateringen är juh frågan. Kör mgcamd 1.35 och jag har ställt in så att den ska uppdatera korten. Den har då iaf med samma inställning lyckats uppdatera c+ kortet som körs på newcs.

[Hugleik]

jag får
encrypted newcamd:xxxxxx-client 192.168.1.1 granted (jag, au=via)
AU flag 0 for user jag när jag startar om oscam

[JoeBlaze]

configurera era servers grappar.

[Hugleik]

Någon som skulle kunna upplysa mig var mitt fel ligger?? =)
som sagt, har funkar i ett par månader men nu tog det stopp.

-------------server----------------------

[reader]

Label = VIA
Protocol = mouse
Detect = cd
Device = /dev/ttyUSB0
mhz = 357
EMMCache = 1,1,2
Group = 1
Caid = 093e
Ident = 093e:000000
BoxID = XXXXXXXX

----------user-------------------

[account]
user = admin
pwd = openpli
group = 1
uniq = 0
AU = VIA
Caid = 093E
Ident = 093E:000000
Monlevel = 0

-----------conf----------------

[global]
nice = -19
WaitForCards = 1



#logging
pidfile         = /var/run/oscam.pid
logfile         = /var/log/oscam.log
usrfile         = /var/log/oscamuser.log
cwlogdir        = /var/log/cw.log
maxlogsize      = 2000

[monitor]
port = 14000
aulow = 120
monlevel = 0

[newcamd]
key = 0710903997494695867299XXXXXX
port = 11201@093E:000000

# web interface
[webif]
httpport      = 8888
httpuser      = admin
httppwd       = admin
httpallowed = 192.168.1.1-192.168.1.255

[JoeBlaze]

ser rätt ut, vad står det när du startar oscam och din user loggar in ? kolla oxå din softcam conf att den ska skicka emm

[Hugleik]

version=0.99.4svn, build #1179, system=i686-pc-linux, nice=-19
2011/03/17 11:21:03 11548 s max. clients=509, client max. idle=120 sec
2011/03/17 11:21:03 11548 s max. logsize=2000 Kb
2011/03/17 11:21:03 11548 s client timeout=5000 ms, fallback timeout=2500 ms, cache delay=0 ms
2011/03/17 11:21:03 11548 s shared memory initialized (size=4178524, id=983045)
2011/03/17 11:21:03 11548 s auth size=4740
2011/03/17 11:21:03 11548 s Cannot open file "/usr/local/etc/oscam.services" (errno=2)
2011/03/17 11:21:03 11548 s userdb reloaded: 0 accounts freed, 11 accounts loaded, 0 expired
2011/03/17 11:21:03 11548 s signal handling initialized (type=sysv)
2011/03/17 11:21:03 11548 s can't open file "/usr/local/etc/oscam.srvid" (err=2), no service-id's loaded
2011/03/17 11:21:03 11549 s monitor: initialized (fd=7, port=14000)
2011/03/17 11:21:03 11549 s camd 3.3x: disabled
2011/03/17 11:21:03 11549 s camd 3.5x: disabled
2011/03/17 11:21:03 11549 s cs378x: disabled
2011/03/17 11:21:03 11549 s newcamd: initialized (fd=8, port=11201, crypted)
2011/03/17 11:21:03 11549 s CAID: 093E
2011/03/17 11:21:03 11549 s provid #0: 000000
2011/03/17 11:21:03 11549 s radegast: disabled
2011/03/17 11:21:03 11549 s resolver thread started
2011/03/17 11:21:03 11549 s logger started (pid=11551)
2011/03/17 11:21:03 11549 s resolver started (pid=11552, delay=30 sec)
2011/03/17 11:21:03 11549 s reader started (pid=11553, device=/dev/ttyUSB0, detect=cd, mhz=357, cardmhz=357)
2011/03/17 11:21:03 11549 s Waiting for local card init ....
2011/03/17 11:21:05 11553 r02 card detected
2011/03/17 11:21:08 11553 r02 ATR: 3F 7D 11 25 02 41 B0 xx xx FF 4A 50 F0 80 00 xx xx xx
2011/03/17 11:21:09 11553 r02 Type: Videoguard Viasat new (093E)
2011/03/17 11:21:11 11553 r02 type: Videoguard, caid: 093E, serial: xxxxxxxx, BoxID: xxxxxx
2011/03/17 11:21:11 11553 r02 ready for requests
2011/03/17 11:21:11 11553 r02 card detected
2011/03/17 11:21:11 11553 r02 type: Videoguard
2011/03/17 11:21:11 11549 s Init for all local cards done !
2011/03/17 11:21:11 11549 s anti cascading disabled
c01 AU flag 0 for user admin
client(1) connect from 192.168.1.1 (pid=11570, pipfd=20)
2011/03/17 11:21:35 11570 c01 encrypted newcamd:11201-client 192.168.1.1 granted (admin, au=via)
2011/03/17 11:21:35 11570 c01 user admin authenticated successfully (using client 6D67)
2011/03/17 11:21:39 11570 c01 admin (093E&000000/0E60/88:6AE2): not found (341 ms



min mg_cfg är denna. från guiden på comhit
# EMM messages
# 00 don't show any EMM's (default)
# 01 show only valid EMM's
# 02 show valid and bad EMM's with complete data display
M: { 01 }

# ECM messages
# 00 don't show any ECM's
# 01 show only valid ECM's (default)
# 02 show valid and bad ECM's with complete data display
C: { 01 }

# AU
# 00 is ignored (default)
# 01 enable AU
# 02 AU Auto
A: { 01 }

# key update
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
U: { 02 }

# key files folder
# 00 keyfiles in /var/keys
# 01 keyfiles in /var/tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
G: { 01 }


# network retry, use summ for several options
# 00 disable (default)
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
N: { 03 }

# network ecm timeout in seconds
K: { 10 }

# newcamd dead routes connect retry, sec
Q: { 60 }

# network shares priority
# 00 newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd
# 02 newcamd, camd3, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
O: { 00 }

# on screen display Options
# 03 default
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
S: { 03 }

# Log options
# 00 Off (default)
# 01 Network
# 02 console
# 03 both
L: { 00 } 172.16.1.1 28007

# cache ecm pids and data used to open channels,
# store pids in /tmp/ca_cache.list at exit, load at startup,
# same syntax as restore.list
# 00 Off (default)
# 01 Ecm pids cache
# 02 Ecm data cache
# 03 both caches
H: { 00 }

# reread files on zap:
# 00 No (default)
# 01 config (including priority and ignore, but not replace/cache)
# 02 config and keys
# 03 both
R: { 00 }

# debug
# 00 off (default)
# 01 on
D: { 00 }

[Hugleik]

newcamd.list

CWS_MULTIPLE = 192.168.1.104 10000: 11201 admin openpli 07 10 90 39 97 49 46 95 86 72 99 xx xx xx lan
CWS_CONNECT_TIMEOUT = 20
CWS_INCOMING_PORT = 12000
CWS_DEBUG_PORT = 1200

[hoggan]

CWS_MULTIPLE = 192.168.1.104 10000: 11201 admin openpli 07 10 90 39 97 49 46 95 86 72 99 xx xx xx lan

Testat så iställe ?
CWS_MULTIPLE = 192.168.1.104 10000:11201 admin openpli 07 10 90 39 97 49 46 95 86 72 99 xx xx xx lan

[99kalle]

newcamd.list

CWS_MULTIPLE = 192.168.1.104 10000: 11201 admin openpli 07 10 90 39 97 49 46 95 86 72 99 xx xx xx lan
CWS_CONNECT_TIMEOUT = 20
CWS_INCOMING_PORT = 12000
CWS_DEBUG_PORT = 1200

varför multiple när du kör med en port på server ta bort 10000 porten och se till att du har 11201 porten riktad mot servern

använd bara CWS =