viasat kort

[shalle]

installerade idag newcs tillsamans med mgcamd fick kortet att hoppa igång men nätverkslampan började blinka som fxxxn vet ej vad det är för fel .
Kör en db800hd med image lt6 postar min newcard list härså får ni se hur den ser ut.
#
CWS = 127.0.0.1 10000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS_CONNECT_TIMEOUT = 20
CWS_INCOMING_PORT = 12000
CWS_KEEPALIVE = yes
#

[vip0963]

kolla i /var/keys/mg_cfg (eller vart den nu ligger på din box) i sektionen:
--------
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 192.168.1.39 8888 /tmp/mgcamd.log
-----------------
kolla så inte det står L: { 01 } vilket betyder att mgcamd skickar loggen ut på nätverket

[shalle]

det stod L 03

[shalle]

resten stämde

[shalle]

hjälpte inte med L 00 blinkar sombara den ändå

[shalle]

så här ser min mgconfig ut .
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 192.168.1.39 8888 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# map all 180x nagra caids to 1801
# default is 01
F: { 01 }

[vip0963]

L: { 03 }
Betyder både val 01 och 02 = 03 så du har både nätverks log och log till konsollen,
startade du om mgcamd efter det att du satt den till L: { 00 } ?

[shalle]

ja det gjorde jag

[shalle]

så här ser min newcamd list .
#
CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS =127.0.0.1 10000
dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

[shalle]

och min newcs xml.

<?xml version="1.0"?>
-<newCSconfig> -<readers name="Card Readers"> -<device> <name>lower</name> <type>Sci</type> <mhz>357</mhz> <node>/dev/sci0</node> <parity>even</parity> <export>yes</export> <enabled>yes</enabled> <blocksa>no</blocksa> <blockua>no</blockua> <blockga>no</blockga> <boxid/> <PTShandshake>no</PTShandshake> <Seca-PPV>no</Seca-PPV> <crypto-special>no</crypto-special> <carddetect>yes</carddetect> <newcamd_port>10000</newcamd_port> <autosid>yes</autosid> <priority>round</priority> </device> -<device> <name>upper</name> <type>Sci</type> <node>/dev/sci1</node> <parity>even</parity> <export>yes</export> <enabled>yes</enabled> <blocksa>no</blocksa> <blockua>no</blockua> <blockga>no</blockga> <boxid/> <PTShandshake>no</PTShandshake> <Seca-PPV>no</Seca-PPV> <crypto-special>no</crypto-special> <carddetect>yes</carddetect> <newcamd_port>10001</newcamd_port> <autosid>yes</autosid> <priority>round</priority> </device> </readers> -<radegastserver> <enabled>no</enabled> <port>10003</port> <allow>ALL</allow> </radegastserver> -<cache> <emm>20</emm> <ecm>-1</ecm> </cache> -<debug> <level>normal</level> <type>init</type> <output>console,udp,tcp</output> <logfile/> <console_options/> <file_options/> <udp_host>192.168.1.100</udp_host> <udp_port>1000</udp_port> <udp_options/> <tcp_port>3001</tcp_port> <tcp_options/> </debug> -<httpd> -<server> <port>8080</port> <enabled>yes</enabled> </server> -<user> <name/> <password/> <accesslevel>admin</accesslevel> </user> </httpd> -<newcamdserver> <enabled>yes</enabled> <deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey> <name>newcs</name> <userfile>/tmp/users.txt</userfile> -<user> <name>dummy</name> <password>dummy</password> <au>on</au> <allow>lower</allow> <allow>upper</allow> </user> </newcamdserver> </newCSconfig>