färdiga filer för com hem ?

[LCarlsson]

hej jag håller på och försöka få igång min 500hd c/t med mitt com hem kort men jag lyckas inte med mgcamd och newcs så än så länge får jag bara in gratiskanalerna....

därför undrar jag om någon skulle kunna dela med sig av sina filer för att få det att fungera

[atomized]

Posta din newcs.xml och din newcamd.list som de ser ut nu så ska jag tala om vad du behöver ändra.

[mattheo]

HD och ComHem lirar väl inte eftersom ComHem använder sig av "pairing"...

[LCarlsson]

okej jag ska få igång ftp först bara. brukar strula med min router....

och ja jag vet att hd inte kommer att fungera men är inte ute efter hd kanalerna

[LCarlsson]

min newcamd.list ser ut såhär

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 127.0.0.1 34000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 34001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
#CWS = 127.0.0.1 34002 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs



och newcs.xml såhär

<?xml version="1.0" ?>
- <!--
For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around )

The configfile are NOT case-sensitive, and shouldnt care about dos/unix cr/lf.

-->
- <newCSconfig>
- <globals>
- <!-- valid value for listening-ip are:
IPv4 adress of local interface.
<listening-ip>127.0.0.1</listening-ip>
-->
</globals>
- <readers name="SCI">
- <device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>600</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
- <!-- <boxkey>0000000000</boxkey>
-->
- <!-- <rsa>0000000000</rsa>
-->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</ipk>
<ucpk>00000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
- <device>
<name>Upper Cardreader</name>
<type>sci</type>
<mhz>358</mhz>
<node>/dev/sci1</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
- <!-- <boxkey>0000000000</boxkey>
-->
- <!-- <rsa>0000000000</rsa>
-->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</ipk>
<ucpk>00000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34001</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
- <radegastserver>
- <!-- valid value for enable are:
Yes, No - Enable or Disable radegast server.
-->
<enabled>No</enabled>
- <!-- valid value for port are:
0,65535 - Which port to listen for incomming connections.
-->
<port>10001</port>
- <allow>
- <!-- valid value for hostname are:
all, IP-address or DNS-name.
-->
<hostname>localhost</hostname>
</allow>
</radegastserver>
- <cache>
- <!-- valid value for emm are:
0-255 - Number of EMM's to cache.
-->
<emm>20</emm>
- <!-- valid value for ecm are:
0-255 - Number of ECM's to cache.
-1 - Dynamic ECM Cache.
-->
<ecm>-1</ecm>
</cache>
- <httpd>
- <server>
- <!-- Port to accept connections on
-->
<port>8080</port>
<enabled>yes</enabled>
</server>
- <user>
- <!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive).
-->
<name>newcs</name>
- <!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive).
-->
<password>newcs</password>
- <!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console
-->
<accesslevel>admin</accesslevel>
</user>
</httpd>
- <debug>
- <!-- valid value for password:
Max 25 characters and minimum 8, this is case-sensitive.
-->
<password>NewCSpwd</password>
- <!-- valid value for mode:
simple, advanced - Set TCP-Console to advanced mode to get access to
potentially dangerous features.
-->
<mode>simple</mode>
- <!-- valid value for level are:
normal, verbose, spam - How extensive debug should be.
-->
<level>normal</level>
- <!-- valid value for type are:
Init, general, ecm, emm, net, all - Section of debug that should be displayed.
-->
<type>general</type>
- <!-- valid value for output are:
Console, udp, tcp, file, all - Where to show debug.
-->
<output>console,tcp</output>
- <!-- console_options are so you can set own loglevel/type for console-logger:
Should hold level and type-tags like above.
-->
<console_options>normal,init</console_options>
- <!-- valid value for logfile are:
Path and filename - Where to write debug logs if file or all is chosed in output.
-->
<logfile>/hdd/newcs.txt</logfile>
- <!-- file_options are so you can set own loglevel/type for file-logger:
Should hold level and type-tags like above.
-->
<file_options>spam,all</file_options>
- <!-- valid value for udp_host are:
IP-address or DNS-name - Where to send debug if udp or all is chosed in output.
-->
<udp_host>192.168.1.10</udp_host>
- <!-- valid value for udp_port are:
0,65535 - Which port to send the udp packets.
-->
<udp_port>1000</udp_port>
- <!-- udp_options are so you can set own loglevel/type for udp-logger:
Should hold level and type-tags like above.
-->
<udp_options>normal,init</udp_options>
- <!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections.
-->
<tcp_port>1001</tcp_port>
- <!-- tcp_options are so you can set own loglevel/type for tcp-logger:
Should hold level and type-tags like above.
-->
<tcp_options>normal,init</tcp_options>
</debug>
- <newcamdserver>
- <!-- valid value for enabled are:
Yes, No - Enable or Disable newcamd server.
-->
<enabled>Yes</enabled>
- <!-- valid value for name are:
Any name - Used to identify server to remote clients,
if the remote client isnt newcamd, this field have no purpouse.
-->
<name>newcs</name>
- <!-- valid value for deskey are:
any 14x2 numbers - Used to encrypt the communication between
the client and the server.
-->
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
- <!-- Notes about users:
The first user doesnt have au without beeing it set to on (unlike newcamd cardserver).
You can add as many user-sections as you want, just put them under eachother.
-->
- <user>
- <!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive).
-->
<name>dummy</name>
- <!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive).
-->
<password>dummy</password>
- <!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname>
-->
- <!-- valid value for port are:
0-65535 - Which port reverse login to the client.
-->
<port>21000</port>
- <!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server.
-->
<au>on</au>
- <!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter.
-->
<sidoverride>off</sidoverride>
- <!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>

-->
- <!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider.
-->
<spider>No</spider>
- <!-- valid value for rate are:
1-60 - number of seconds between each ecm
-->
<rate>2</rate>
- <!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port.
-->
<cardlevel>1</cardlevel>
</user>
- <user>
- <!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive).
-->
<name>mpcs</name>
- <!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive).
-->
<password>dummy</password>
- <!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname>
-->
- <!-- valid value for port are:
0-65535 - Which port reverse login to the client.
-->
<port>21000</port>
- <!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server.
-->
<au>on</au>
- <!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter.
-->
<sidoverride>off</sidoverride>
- <!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>

-->
- <!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider.
-->
<spider>No</spider>
- <!-- valid value for rate are:
1-60 - number of seconds between each ecm
-->
<rate>2</rate>
- <!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port.
-->
<cardlevel>1</cardlevel>
</user>
</newcamdserver>
- <chameleon2>
- <server>
- <!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections.
-->
<port>1234</port>
- <!-- enable or disable the server, valid values are yes/no
-->
<enabled>No</enabled>
</server>
- <peer>
- <!-- Connect to remote Chamelon server with the below credentials
-->
<hostname>localhost</hostname>
- <!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections.
-->
<port>1234</port>
- <!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive).
-->
<name>myname</name>
- <!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive).
-->
<password>mypassword</password>
- <!-- Not yet implemented, this will be how chameleon will connect to more than one network
-->
<realm>myShares</realm>
</peer>
- <user>
- <!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive).
-->
<name>myname</name>
- <!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive).
-->
<password>mypassword</password>
- <!-- Not yet implemented, this will be how chameleon will connect to more than one network
-->
<realm>myShares</realm>
</user>
</chameleon2>
</newCSconfig>

[atomized]

Oj, det var en fruktansvärt grötig newcs.xml. Men jag såg inga uppenbara fel i filerna. Det finns en chans att det borde funkat med de filerna. Men jag har rensat filerna lite så du kan testa med dessa:

newcs.xml

<newCSconfig>
<readers name="SCI">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>358</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<crypto-special>No</crypto-special>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<Seca-PPV>no</Seca-PPV>
<priority>round</priority>
</device>
<device>
<name>Upper Cardreader</name>
<type>sci</type>
<mhz>358</mhz>
<node>/dev/sci1</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<crypto-special>No</crypto-special>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34001</newcamd_port>
<Seca-PPV>no</Seca-PPV>
<priority>round</priority>
</device>
</readers>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>newcs</name>
<password>newcs</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password>NewCSpwd</password>
<mode>simple</mode>
<level>normal</level>
<type>general</type>
<output>console,tcp</output>
<console_options>normal,init</console_options>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<spider>No</spider>
</user>
<user>
<name>mpcs</name>
<password>dummy</password>
<au>on</au>
<spider>No</spider>
</user>
</newcamdserver>
</newCSconfig>

newcamd.list

CWS_KEEPALIVE = 300
CWS = 127.0.0.1 34000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 127.0.0.1 34001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

Om det ändå inte vill fungera så kolla att newcs och mgcamd är igång. Har du ställt in i menyerna att de ska starta vid uppstart? Brukar heta "services to run" eller något liknande i menyerna.

Annars om du är van vid Linuxprompten kan du kolla att de går med kommando:
ps ax | grep newcs
resp.
ps ax | grep mgcamd

[LCarlsson]

jag fick igång det ändå med hjälp av CCcam och lite trixande

men jag får tacka väldigt mycket för din hjälp ändå och jag sparar dina filer om de behövs senare om jag ändrar någonting