kört fast med d500

[lakens]

Jag har ändrat cws raden, gjorde ingen skillnad.
när jag startar mgcamd i prompten står det.
dmx_set_filter error 9: bad file descriptior
och det rullar på hela tiden.
God morgon föresten

[atomized]

Det står nog saker innan också men de hinner du väl inte se...
Det troliga är att du har något knas i dina config-filer. Mgcamd använder två config filer och båda ska finnas i /var/keys eller /usr/keys. De två filerna heter newcamd.list och mg_cfg. Du måste se till att båda finns där och att de är läsbara och inte skadade på något sätt. Filen mg_cfg installerades förmodligen automatiskt i installationen av mgcamd och i första läget ska du inte behöva ändra något i den.

Du kan logga in på boxen och skriva kommandot:
ls -al /var/keys

så ser vi vilka filer du har i /var/keys.


Och en annan sak:
När man startar om mgcamd är det viktigt att man först stoppar den mgcamd som är igång så man inte får flera mgcamd körande på samma gång. Så kör alltid
killall mgcamd
innan du startar mgcamd

[optimal]

Har du satt box type på 06 i mg_cfg

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }

[lakens]

jotuxbox mgcamd v1.35a by mixvt (compiled Jan 26 2010 15:59:04)
[mg] Net:1:7:0:5s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log:3:172.16.1.1:28007 Reread:0
[mg] Ecm cache time: 15
Box type: mips dreambox (dm7025, dm800)
/dev/dvb/adapter0/ca0 error 2: No such file or directory
/dev/dvb/adapter0/ca1 error 2: No such file or directory
/dev/dvb/adapter0/ca2 error 2: No such file or directory
/dev/dvb/adapter0/ca3 error 2: No such file or directory
Conax.Key error 2: No such file or directory
Keys readed
AutoRoll.Key error 2: No such file or directory
Conax.Key error 2: No such file or directory
newcamd keep alive: 300, incoming port: 0
root@dm500 ~ # [mgcam] emm thread started
got 103 cmd 9F
[mg0] namespace 300000 t-id 15 on-id 56
[mg0] descramble on 1, source 0
[mg0] service D66 index 0 pmt pid D66 (1), pids: video 0x0D67, audio 0x0D68 0x0D69 0x0D6A
[mg0] ECM: CaID: 0x090F -> CaPID: 0x0D6F ProvID: 000000
[mg0] ECM: CaID: 0x093E -> CaPID: 0x0108 ProvID: 000000
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
[mgcamd] emm started
[mgcamd] emm stopped
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_STOP error 9: Bad file descriptor
DMX_SET_FILTER error 9: Bad file descriptor
DMX_STOP e

ag har ändrat till b 06 så här såg det ut innan

[lakens]

drwx------ 2 root root 0 May 4 14:21 .
drwx------ 13 root root 0 Jun 25 2008 ..
-rw-r--r-- 1 root root 0 Jan 1 1970 SoftCam.Key
-rw------- 1 root root 212 Jun 25 2008 ignore.list.example
-rw-r--r-- 1 root root 0 Jan 1 1970 irdeto
-rw------- 1 root root 3784 May 4 14:16 mg_cfg
-rw-r--r-- 1 root root 111 May 5 09:02 newcamd.list
-rw------- 1 root root 241 Jun 25 2008 newcamd.list.example
-rw------- 1 root root 986 Jun 25 2008 peer.cfg.example
-rw------- 1 root root 117 Jun 25 2008 priority.list.example
-rw------- 1 root root 345 Jun 25 2008 replace.list.example
och nästa komando såg ut så här

[atomized]

Som optimal säger, du ska ha
B: { 06 }
i mg_cfg. Tänkte inte på det men det måste ändras när man kör OpenPLI 3.0 på Dreambox.

Jag måste ut i solskenet med familjen nu så jag kommer inte tillbaka förrän i eftermiddag nån gång. Du får fortsätta experimentera på egen hand eller om du kan få hjälp av någon annan.
Lycka till!

[lakens]

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 06 }
Tack för all hjälp så länge.Så här ser mg_cfg filen ut