dreambox 800 se server och klient mgcamd newcs

[gortex]

Kan man ha ett kort i en dreambox 800 se och installera newcs som server och mgcamd som client så den använder sig som både server och client?
får det inte och fungera men när jag använder en relook som server och dreambox som client fungerar det utan problem.

kan någon peka ut något exempel med beskrivning, kör enigma 2 3.3
va snälla i svaren jag är ny på detta

[optimal]

Det går bra det, posta configfilerna för dm800 så får du nog hjälp. (newcs.xml)(newcamd.list)

[gortex]

<?xml version="1.0"?>
<!--

For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around )

The configfile are NOT case-sensitive, and shouldnt care about dos/unix cr/lf.
-->

<newCSconfig>
<globals>
<!-- valid value for listening-ip are:
IPv4 adress of local interface.
<listening-ip>192.168.0.3</listening-ip> -->
</globals>
<readers name="SCI">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>600</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<!-- <rsa>0000000000</rsa> -->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</ipk>
<ucpk>00000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
<cache>
<!-- valid value for emm are:
0-255 - Number of EMM's to cache. -->
<emm>20</emm>

<!-- valid value for ecm are:
0-255 - Number of ECM's to cache.
-1 - Dynamic ECM Cache. -->
<ecm>-1</ecm>
</cache>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>

<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>

<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<!-- valid value for password:
Max 25 characters and minimum 8, this is case-sensitive. -->
<password>NewCSpwd</password>

<!-- valid value for mode:
simple, advanced - Set TCP-Console to advanced mode to get access to
potentially dangerous features.-->
<mode>simple</mode>

<!-- valid value for level are:
normal, verbose, spam - How extensive debug should be. -->
<level>normal</level>

<!-- valid value for type are:
Init, general, ecm, emm, net, all - Section of debug that should be displayed. -->
<type>general</type>

<!-- valid value for output are:
Console, udp, tcp, file, all - Where to show debug. -->
<output>console,tcp</output>

<!-- console_options are so you can set own loglevel/type for console-logger:
Should hold level and type-tags like above. -->
<console_options>normal,init</console_options>

<!-- valid value for logfile are:
Path and filename - Where to write debug logs if file or all is chosed in output. -->
<logfile>/hdd/newcs.txt</logfile>

<!-- file_options are so you can set own loglevel/type for file-logger:
Should hold level and type-tags like above. -->
<file_options>spam,all</file_options>

<!-- valid value for udp_host are:
IP-address or DNS-name - Where to send debug if udp or all is chosed in output. -->
<udp_host>192.168.1.10</udp_host>

<!-- valid value for udp_port are:
0,65535 - Which port to send the udp packets. -->
<udp_port>1000</udp_port>

<!-- udp_options are so you can set own loglevel/type for udp-logger:
Should hold level and type-tags like above. -->
<udp_options>normal,init</udp_options>

<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<tcp_port>1001</tcp_port>

<!-- tcp_options are so you can set own loglevel/type for tcp-logger:
Should hold level and type-tags like above. -->
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<!-- valid value for enabled are:
Yes, No - Enable or Disable newcamd server. -->
<enabled>Yes</enabled>

<!-- valid value for name are:
Any name - Used to identify server to remote clients,
if the remote client isnt newcamd, this field have no purpouse. -->
<name>newcs</name>

<!-- valid value for deskey are:
any 14x2 numbers - Used to encrypt the communication between
the client and the server. -->
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>

<!-- Notes about users:
The first user doesnt have au without beeing it set to on (unlike newcamd cardserver).
You can add as many user-sections as you want, just put them under eachother. -->
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>dummy</name>

<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>dummy</password>

<!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname> -->
<!-- valid value for port are:
0-65535 - Which port reverse login to the client. -->
<port>21000</port>

<!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server. -->
<au>on</au>

<!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter. -->
<sidoverride>off</sidoverride>

<!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>
-->
<!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider. -->
<spider>No</spider>

<!-- valid value for rate are:
1-60 - number of seconds between each ecm -->
<rate>2</rate>

<!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port. -->
<cardlevel>1</cardlevel>
</user>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>mpcs</name>

<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>dummy</password>

<!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname> -->
<!-- valid value for port are:
0-65535 - Which port reverse login to the client. -->
<port>21000</port>

<!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server. -->
<au>on</au>

<!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter. -->
<sidoverride>off</sidoverride>

<!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>
-->
<!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider. -->
<spider>No</spider>

<!-- valid value for rate are:
1-60 - number of seconds between each ecm -->
<rate>2</rate>

<!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port. -->
<cardlevel>1</cardlevel>
</user>
</newcamdserver>
<chameleon2>
<server>
<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<port>1234</port>
<!-- enable or disable the server, valid values are yes/no -->
<enabled>No</enabled>
</server>
<peer> <!-- Connect to remote Chamelon server with the below credentials -->
<hostname>localhost</hostname>
<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<port>1234</port>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>myname</name>
<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>mypassword</password>
<!-- Not yet implemented, this will be how chameleon will connect to more than one network -->
<realm>myShares</realm>
</peer>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>myname</name>
<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>mypassword</password>
<!-- Not yet implemented, this will be how chameleon will connect to more than one network -->
<realm>myShares</realm>
</user>
</chameleon2>
</newCSconfig>



CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.0.5 10000 user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 192.168.0.5 10001 user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
#CWS = 127.0.0.1 34002 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

[gortex]

<?xml version="1.0"?>
<!--

For setup-issues, look in readme.txt!
If there are other troubles, try different forums or irc channels around )

The configfile are NOT case-sensitive, and shouldnt care about dos/unix cr/lf.
-->

<newCSconfig>
<globals>
<!-- valid value for listening-ip are:
IPv4 adress of local interface.
<listening-ip>192.168.0.3</listening-ip> -->
</globals>
<readers name="SCI">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>600</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<!-- <boxkey>0000000000</boxkey> -->
<!-- <rsa>0000000000</rsa> -->
<irdeto-camkey>0000000000000000</irdeto-camkey>
<irdeto-camkey-data>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</irdeto-camkey-data>
<crypto-special>No</crypto-special>
<ipk>000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000</ipk>
<ucpk>00000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 00000000000000000000000000000000000000000000000000 000000000000</ucpk>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<autosid>Yes</autosid>
<Seca-PPV>no</Seca-PPV>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
<cache>
<!-- valid value for emm are:
0-255 - Number of EMM's to cache. -->
<emm>20</emm>

<!-- valid value for ecm are:
0-255 - Number of ECM's to cache.
-1 - Dynamic ECM Cache. -->
<ecm>-1</ecm>
</cache>
<httpd>
<server> <!-- Port to accept connections on -->
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for browser to logon (its case sensitive). -->
<name>newcs</name>

<!-- valid value for password are:
Any password you'd like - Used for browser to logon (its case sensitive). -->
<password>newcs</password>

<!-- valid value for accesslevel are:
admin, stats - Define what rights the user has in the web-console -->
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<!-- valid value for password:
Max 25 characters and minimum 8, this is case-sensitive. -->
<password>NewCSpwd</password>

<!-- valid value for mode:
simple, advanced - Set TCP-Console to advanced mode to get access to
potentially dangerous features.-->
<mode>simple</mode>

<!-- valid value for level are:
normal, verbose, spam - How extensive debug should be. -->
<level>normal</level>

<!-- valid value for type are:
Init, general, ecm, emm, net, all - Section of debug that should be displayed. -->
<type>general</type>

<!-- valid value for output are:
Console, udp, tcp, file, all - Where to show debug. -->
<output>console,tcp</output>

<!-- console_options are so you can set own loglevel/type for console-logger:
Should hold level and type-tags like above. -->
<console_options>normal,init</console_options>

<!-- valid value for logfile are:
Path and filename - Where to write debug logs if file or all is chosed in output. -->
<logfile>/hdd/newcs.txt</logfile>

<!-- file_options are so you can set own loglevel/type for file-logger:
Should hold level and type-tags like above. -->
<file_options>spam,all</file_options>

<!-- valid value for udp_host are:
IP-address or DNS-name - Where to send debug if udp or all is chosed in output. -->
<udp_host>192.168.1.10</udp_host>

<!-- valid value for udp_port are:
0,65535 - Which port to send the udp packets. -->
<udp_port>1000</udp_port>

<!-- udp_options are so you can set own loglevel/type for udp-logger:
Should hold level and type-tags like above. -->
<udp_options>normal,init</udp_options>

<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<tcp_port>1001</tcp_port>

<!-- tcp_options are so you can set own loglevel/type for tcp-logger:
Should hold level and type-tags like above. -->
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<!-- valid value for enabled are:
Yes, No - Enable or Disable newcamd server. -->
<enabled>Yes</enabled>

<!-- valid value for name are:
Any name - Used to identify server to remote clients,
if the remote client isnt newcamd, this field have no purpouse. -->
<name>newcs</name>

<!-- valid value for deskey are:
any 14x2 numbers - Used to encrypt the communication between
the client and the server. -->
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>

<!-- Notes about users:
The first user doesnt have au without beeing it set to on (unlike newcamd cardserver).
You can add as many user-sections as you want, just put them under eachother. -->
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>dummy</name>

<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>dummy</password>

<!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname> -->
<!-- valid value for port are:
0-65535 - Which port reverse login to the client. -->
<port>21000</port>

<!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server. -->
<au>on</au>

<!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter. -->
<sidoverride>off</sidoverride>

<!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>
-->
<!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider. -->
<spider>No</spider>

<!-- valid value for rate are:
1-60 - number of seconds between each ecm -->
<rate>2</rate>

<!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port. -->
<cardlevel>1</cardlevel>
</user>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>mpcs</name>

<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>dummy</password>

<!-- valid value for hostname are:
IP-address or DNS-name - Used for reverse login to the client.
<hostname>127.0.0.1</hostname> -->
<!-- valid value for port are:
0-65535 - Which port reverse login to the client. -->
<port>21000</port>

<!-- valid value for au are:
On,Off - Wheather the client are allowed to send EMM to the server. -->
<au>on</au>

<!-- valid value for sidoverride are:
On,Off - Wheather the client are allowed to override the SID-filter. -->
<sidoverride>off</sidoverride>

<!-- valid value for readers are device name,
if one <allow> present, other readers will be disabled!
<readers>
<allow>Cardreader</allow>
</readers>
-->
<!-- valid value for spider are:
Yes,No - Wheather the client are allowed to be newcamd Cardspider. -->
<spider>No</spider>

<!-- valid value for rate are:
1-60 - number of seconds between each ecm -->
<rate>2</rate>

<!-- valid value for cardlevel are:
1 - If its set Mgcamd will use all cards over the same port. -->
<cardlevel>1</cardlevel>
</user>
</newcamdserver>
<chameleon2>
<server>
<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<port>1234</port>
<!-- enable or disable the server, valid values are yes/no -->
<enabled>No</enabled>
</server>
<peer> <!-- Connect to remote Chamelon server with the below credentials -->
<hostname>localhost</hostname>
<!-- valid value for tcp_port are:
0,65535 - Which port to listen for incomming tcp connections. -->
<port>1234</port>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>myname</name>
<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>mypassword</password>
<!-- Not yet implemented, this will be how chameleon will connect to more than one network -->
<realm>myShares</realm>
</peer>
<user>
<!-- valid value for userfile are:
Any username you'd like - Used for client to logon (its case sensitive). -->
<name>myname</name>
<!-- valid value for password are:
Any password you'd like - Used for client to logon (its case sensitive). -->
<password>mypassword</password>
<!-- Not yet implemented, this will be how chameleon will connect to more than one network -->
<realm>myShares</realm>
</user>
</chameleon2>
</newCSconfig>



CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = 192.168.0.5 10000 user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
CWS = 192.168.0.5 10001 user password 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs
#CWS = 127.0.0.1 34002 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

[optimal]

Orkar inte läsa det där
Prova det här

<?xml version="1.0"?>
<newCSconfig>
<readers name="Standard Phoenix on DM800">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>368</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>no</blocksa>
<blockua>no</blockua>
<blockga>yes</blockga>
<blockC0>yes</blockC0>
<carddetect>no</carddetect>
<newcamd_port>10001</newcamd_port>
<autosid>Yes</autosid>
<pincode>0000</pincode>
<priority>round</priority>
</device>
</readers>
<radegastserver>
<enabled>no</enabled>
<port>10001</port>
<allow>
<hostname>localhost</hostname>
</allow>
</radegastserver>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<server>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>newcs</name>
<password>newcs</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password>sdu-</password>
<mode>advanced</mode>
<level>internal</level>
<type>all</type>
<output>console,tcp</output>
<tcp_port>1111</tcp_port>
<tcp_options>normal,init</tcp_options>
<logfile>media/hdd/newcs.txt</logfile>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>ruska</name>
<password>tupp</password>
<au>on</au>
<sidoverride>off</sidoverride>
<spider>No</spider>
<cardlevel>1</cardlevel>
</user>
</newcamdserver>
<chameleon2>
<server>
<port>1234</port>
<enabled>no</enabled>
<realm>myShares</realm>
</server>
<peer>
<hostname>remote</hostname>
<port>1234</port>
<name>myname</name>
<password>mypassword</password>
<realm>myShares</realm>
</peer>
<user>
<name>myname</name>
<password>mypassword</password>
<realm>myShares</realm>
</user>
</chameleon2>
</newCSconfig>

CWS = 127.0.0.1 10001 ruska tupp 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

[matkoh]

Hmmmm.

Men snälla, om ni ska posta en konfig så ta bort kommentarsraderna, det är totalt oläsbart annars. vem orkar läsa !! Och för er som inte vet, förstår eller... så börjar kommentarsrader med # eller <!-- & avslutas med -->

[atomized]

Håller med ovanstående om att det är en "real pain in the ass" att läsa sådana där automatgenererade config-filer med tonvis med skräp i.

Men jag har gjort mig besväret att rensa din konfig från allt onödigt och nu ser den plötsligt vettig ut.
Mitt tips är att skita i sådana där config-generators och istället skriva din konfig för hand. Då har du en chans att faktiskt förstå varenda rad och vad den är bra för. När det gäller newcs kan man gärna utgå från den "default-config" jag tipsat om i detta inlägg:
http://www.comhit.net/showthread.php...l=1#post127474

Här är din konfig som den borde se ut:

<newCSconfig>
<readers name="SCI">
<device>
<name>Lower Cardreader</name>
<type>sci</type>
<mhz>357</mhz>
<node>/dev/sci0</node>
<parity>odd</parity>
<reset>normal</reset>
<export>Yes</export>
<enabled>Yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<crypto-special>No</crypto-special>
<PTShandshake>No</PTShandshake>
<carddetect>yes</carddetect>
<newcamd_port>34000</newcamd_port>
<Seca-PPV>no</Seca-PPV>
<priority>round</priority>
</device>
</readers>
<cache>
<emm>20</emm>
<ecm>-1</ecm>
</cache>
<httpd>
<port>8080</port>
<enabled>yes</enabled>
</server>
<user>
<name>newcs</name>
<password>newcs</password>
<accesslevel>admin</accesslevel>
</user>
</httpd>
<debug>
<password>NewCSpwd</password>
<level>verbose</level>
<type>init</type>
<output>console,tcp</output>
<console_options>normal,init</console_options>
<tcp_port>1001</tcp_port>
<tcp_options>normal,init</tcp_options>
</debug>
<newcamdserver>
<enabled>Yes</enabled>
<name>newcs</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<user>
<name>dummy</name>
<password>dummy</password>
<au>on</au>
<spider>No</spider>
</user>
</newcamdserver>
</newCSconfig>

CWS_KEEPALIVE = 300
CWS = 127.0.0.1 34000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs

[gortex]

tack autmized du är mycket snäll, ska prova den.
Matkoh jag skrev att jag är ny sorry föddes inte med en dreambox

[gortex]

har provat båda alternativen som postats men det går inte.

den fungerar hur bra som helst som en MGCAMD eller CCAM client mot en relook, men det fungerar inte när dremboxen ska vara server och client.
är det någon som varit med om liknande?
nedan är newcs.xml som finns på relooken och som fungerar när dreamboxen är client
jag flashar den med newenigma2 4.03 trycker blå knapp laddar new mgcamd1.3 newcs1.6 ändrar filerna enligt er spec funkar inte.
tar bort newcs ändrar så den använder mgcamd och relooken som newcs server fungerar direkt


CCAM
N: 192.168.0.5 10000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 192.168.0.5 10001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14

mgcamd
CWS = 192.168.0.5 10001 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14
CWS = 192.168.0.5 10000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14

newcs.xml
<newCSconfig>
<readers name="Card Readers">
<device>
<name>lower</name>
<type>Sci</type>
<node>/dev/sci0</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<boxkey>0000000000</boxkey>
<PTShandshake>yes</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10001</newcamd_port>
<priority>round</priority>
</device>
<device>
<name>upper</name>
<type>Sci</type>
<node>/dev/sci1</node>
<export>yes</export>
<enabled>yes</enabled>
<blocksa>No</blocksa>
<blockua>No</blockua>
<blockga>No</blockga>
<boxkey>0000000000</boxkey>
<PTShandshake>yes</PTShandshake>
<crypto-special>no</crypto-special>
<carddetect>yes</carddetect>
<newcamd_port>10000</newcamd_port>
<priority>round</priority> <!-- hard is default -->
</device>
</readers>
<cache>
<emm>10</emm>
<ecm>-1</ecm>
</cache>
<debug>
<level>normal</level>
<type>init</type>
<output>tcp,console</output>
<logfile></logfile>
<console_options></console_options>
<file_options></file_options>
<udp_host>192.168.1.10</udp_host>
<udp_port>1000</udp_port>
<udp_options></udp_options>
<tcp_port>3001</tcp_port>
<tcp_options></tcp_options>
</debug>
<newcamdserver>
<enabled>yes</enabled>
<name>MOJSERVER</name>
<deskey>01 02 03 04 05 06 07 08 09 10 11 12 13 14</deskey>
<userfile>/tmp/users.txt</userfile>
<user>
<name>dummy</name>
<password>dummy </password>
<au>on</au>
</user>
<user>
<user>
<name>server</name>
<password>server-pass</password>
<au>on</au>
</user>
</newcamdserver>
</newCSconfig>

[atomized]

Och du sätter i kortet åt rätt håll i Dreamboxen?

Du får dela upp felsökningen i två steg:

1. Kolla så att serverdelen newcs funkar.
Flasha Dreamboxen och installera newcs samt mgcamd. Ändra filerna som jag beskrivit.
Från en PC på samma nät surfar du till newcs webinterface http://<dream-ip>:8080
(istället för <dream-ip> skriver du givetvis IP-adressen till din Dreambox.)
Logga in som newcs med lösenord newcs
Klicka runt i webinterfacet. Leta efter Entitlements. Prova att lista entitlements från kortet. Får du då fram ett antal rader med datum på slutet så funkar newcs och serverdelen.

2. Kolla klientdelen mgcamd.
När serverdelen funkar så kan du felsöka mgcamd. Logga in i boxen och skriv kommando:
killall mgcamd
för att stoppa mgcamd
Starta mgcamd igen genom att skriva
mgcamd
Läs meddelanden som kommer på skärmen och se vad den klagar på.