Sorry for the dummies-thing but here is a description on how I got it to work.
First I start multiprog an set my MP 3.5 in phoenix mode 3.58 mhz. Then I open my winexplorer and load the CDupdate.xvb A bit down in the script You will find these lines
"This is what you need to change, serialnumber and perhaps endDate
serial = "xx xx xx xx" ' Four last bytes of your serialnumber"
Hmmm... what should I type in where the xx xx xx xx is? Turn your original card around and U will find some numbers they will look like this 011 3xxx xxxx-x. Let´s say your cardnumber is 011 3123 4567-8 in my case i just took 5678 and added a zero in front of each digit so it looked like this 05 06 07 08and put these digits in the cdupdate.xvb so it looked like this:
This is what you need to change, serialnumber and perhaps endDate
serial = "05 06 07 08 " ' Four last bytes of your serialnumber
Next thing is to have the right settings in the winexplorer. If U copy these and paste them in to your winexplorer.ini file
[Card Settings]
1=VIACCESS
2=Conax
3=conax 18 days
4=conax3
5=Unlooper
[VIACCESS]
BaudRate=9600
ResetBaudRate=9600
ResetDelay=40000
ByteDelay=40000
RxByteTimeout=200
Parity=1
StopBits=2
FlushBeforeWrite=1
FlushEchoByte=1
DTRControl=1
RTSControl=0
ResetMode=1
IgnoreTimeouts=1
ResetAfterTimeout=0
ResetLine=0
LogTransactions=0
DisplayUSW=0
DisplayFuse=0
ByteConvention=0
[Window Settings]
MainWidth=808
MainHeight=580
MainTop=-4
MainLeft=-4
BatchWidth=275
OutputHeight=260
BatchHidden=1
OutputHidden=0
[Serial Settings]
Device=com1:
BaudRate=9600
ResetBaudRate=9600
ResetDelay=100
ByteDelay=100
Parity=2
StopBits=2
ByteConvention=1
FlushBeforeWrite=1
RxByteTimeout=400
FlushEchoByte=1
[Advanced]
IgnoreTimeouts=1
ResetMode=1
ResetAfterTimeout=0
DTRControl=1
RTSControl=0
ResetLine=0
[Conax]
BaudRate=9600
ResetBaudRate=9600
ResetDelay=2000
ByteDelay=4000
RxByteTimeout=200
Parity=2
StopBits=2
FlushBeforeWrite=0
FlushEchoByte=1
DTRControl=1
RTSControl=0
ResetMode=1
IgnoreTimeouts=0
ResetAfterTimeout=0
ResetLine=0
LogTransactions=0
DisplayUSW=0
DisplayFuse=0
ByteConvention=1
[conax 18 days]
BaudRate=9600
ResetBaudRate=9600
ResetDelay=50000
ByteDelay=50000
RxByteTimeout=2000
Parity=2
StopBits=0
FlushBeforeWrite=0
FlushEchoByte=1
DTRControl=1
RTSControl=0
ResetMode=1
IgnoreTimeouts=0
ResetAfterTimeout=0
ResetLine=0
LogTransactions=1
DisplayUSW=1
DisplayFuse=1
ByteConvention=0
[Conax3]
BaudRate=9600
ResetBaudRate=9600
ResetDelay=100
ByteDelay=100
RxByteTimeout=400
Parity=2
StopBits=2
FlushBeforeWrite=1
FlushEchoByte=1
DTRControl=1
RTSControl=0
ResetMode=1
IgnoreTimeouts=1
ResetAfterTimeout=0
ResetLine=0
LogTransactions=0
DisplayUSW=0
DisplayFuse=0
ByteConvention=1
[Unlooper]
BaudRate=9600
ResetBaudRate=9600
ResetDelay=2000
ByteDelay=4000
RxByteTimeout=200
Parity=2
StopBits=2
FlushBeforeWrite=1
ByteConvention=1
FlushEchoByte=1
DTRControl=0
RTSControl=0
ResetMode=1
IgnoreTimeouts=1
ResetAfterTimeout=0
ResetLine=0
LogTransactions=0
DisplayUSW=0
DisplayFuse=0
[Advanced]
IgnoreTimeouts=1
ResetMode=1
ResetAfterTimeout=0
DTRControl=0
RTSControl=0
ResetLine=0
Open the settings in winexplorer and choose conax3
U are now ready to MOSC your card! Put it in to your MP3.5 and press the "run script" button When the script is done U can put the card in your reciver and wait. I got picture on all channels exept Kiosk.
Now it´s up to U if U will get it to work GOOD LUCK
"Only dead fishes follows the stream"
Jesse©
Svara med citat
